A garage door that sits uneven, with one bottom corner higher than the other or a wider gap on one side, usually has a problem with a lift cable, a roller, a track, or the spring balance. Stop running the door. Another cycle can pull it further out of line, so record how it sits now from a safe distance.

Why another open or close cycle makes it worse

A garage door rises evenly only when both sides share the load. Each bottom corner hangs from a lift cable, a steel cable that runs up the side of the door to a drum above the opening. Rollers on each edge ride inside the tracks. When the door sits crooked, one of those connections has stopped doing its share, and the other side is carrying more than it should.

Running the opener again asks a door that is already out of square to travel anyway. The opener keeps pulling even when one side binds. The low side can drag, a roller can climb out of its track, and a cable that is barely holding can jump off its drum. The door can also jam partway and drop on the weak side.

There is a second reason to wait. The way the door sits right now is the clearest clue anyone will get. Another cycle can shift it and hide what failed first.

What to note from a safe distance

Stand outside the door's path and look without touching the cables, springs, brackets, or the door itself. A few phone photos and short written notes capture the details that matter when you describe the problem.

  • Which bottom corner is lower, left or right, as seen from inside the garage.
  • Whether the gap between the door and the frame looks even down both sides and across the top, or wider in one spot.
  • Whether the panels look straight or bowed, creased, or pulled apart at a seam.
  • Whether either lift cable looks slack, hangs away from the door, or is missing from where it normally runs.
  • Where the door stopped: closed, a few feet up, or near the top.
  • What was happening at that moment, and any bang or scraping sound you heard.

Write the notes down now. Details like which side made the noise fade quickly.

How the common patterns look different

None of these is a diagnosis. They are the broad shapes an uneven door tends to take, and each points toward a likely area for a technician to confirm in person.

One side hanging lower

When one bottom corner sits lower but the door still looks square in its tracks, the trouble is often with that side's lift cable or drum, or the rollers along that edge. A cable that has frayed, slipped, or come off its drum stops holding its corner, so the door sags there.

Door tilted with an edge out of the track

If one edge of the door has swung toward or away from the frame, look at the rollers along that edge. A roller sitting outside its track, or a track bent outward, lets the edge wander. The door looks twisted in the opening rather than simply lower on one side.

Uneven lifting across the whole door

A door that hangs low across its full width, or seems to struggle on both sides rather than one, points more toward balance. The springs carry most of the door's weight, and when that support weakens, the whole door rides wrong instead of one corner.

Panels bowed or separated

Sometimes the cables and rollers are holding and the panels themselves are the problem. A bowed section or a hinge pulling away can make the door look uneven. A straight-on photo shows this well, because the bottom edge stays fairly level while the face of the door does not.

The safe next step and what to say on the call

Leave the door where it is. Don't press the wall button or remote, and don't pull the opener's release cord, the handle that disconnects the door from the opener. On an uneven door, releasing it can let the heavy side drop suddenly. Keep people and pets out from under the door, and don't drive through a partly open, crooked door.

When you call Dallas Metro Garage Door at (469) 491-7394, say which side is low, where the door stopped, what you heard, and whether a cable looks loose, and mention that you have photos. That description gives a sense of whether cables and rollers, springs, or panels are involved, though the door itself still has to be seen.

If the door is stuck open or hanging so the garage cannot be closed, say so at the start of the call. Dallas Metro Garage Door offers emergency garage door service for doors that cannot be secured.

Frequently asked questions

Can I lift the door by hand to even it out?

Lifting an uneven garage door by hand is not a safe fix. The door is heavy, and when a cable or roller on one side has stopped holding, the weight is no longer shared evenly. Lifting can shift that load suddenly or let the low side drop. Leave the door where it sits and keep clear of it.

Does it matter whether the door was moving or stopped when I noticed it was crooked?

Yes. A garage door that went crooked while moving, especially with a bang or scraping sound, suggests something gave way during travel, such as a cable or roller. A door you found already sitting crooked tells a different story. Note which one you saw, since that timing helps narrow down where to look.

Which photos are most useful to take?

For an uneven garage door, the most useful photos are a straight-on shot from inside showing the whole door and both bottom corners, a closer view of each side where the rollers meet the track, and a shot of each lift cable. Take them from where you stand, without stepping under the door.

All articles